series amegr8-kz-c1 up to 350ma | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r1.b 1 of 2 north america only features: models single output model max output power (w) * output voltage range (v) output current (ma) input voltage (vac/hz) efficiency (%) AMEGR8-2435KZ-C1 8.4 12-24 32525 90-264/ 47-63 80 * exceeding the maximum output power w ill permanently damage the converter note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters conditions typical maximum units voltage range 90-264vac vac inrush current <2ms 115v 10 a 230v 20 leakage current 230v 0.25 ma ac current 115v 0.03 a 230v 0.01 no-load consumption 0.7 w external fuse 250v/1.5a power factor 0.85 output specifications parameters conditions typical maximum units current accuracy 10 % line regulation ll-hl 5 % load regulation 0% to 100% load 10 % ripple & noise 20mhz bandwidth 150 mv p-p hold-up time (min) 100% load 4 8 ms isolation specifications parameters conditions typical maximum units tested i/o voltage 5ma/60sec 3000 3750 vac input fg 1500 vac isolation resistance >50 m ? general specifications parameters conditions typical maximum units switching frequency 100 khz over current protection 115 % over voltage protection zener diode clamp short circuit protection continuous, auto recovery operating temperature * -30 to +55 o c temperature rise 25 o c storage temperature -40 to +80 o c temperature coefficient 0.05 % / o c cooling free air convection ? ac-dc constant current led driver ? waterproof ip67 ? universal input: 90-264vac, 47-63hz ? over current protection ? short circuit protection ? over voltage protection ? rohs compliant ? power factor correction
series amegr8-kz-c1 up to 350ma | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r1.b 2 of 2 north america only general specifications (continued) parameters conditions typical maximum units humidity 95 % rh case material aluminum potting white epoxy (ip67 rated) wires ul1015 18awg *20cm weight 178 g dimensions (l x h x w) 6.30 x 0.98 x 0.87inches 160.00 x 25.00 x 22.00mm mtbf 50,000 hrs (mil-hdbk-217 f at +25 o c) * note: converters do not have over temperature protection and will be damaged if their maximum case temperature is exceeded. safety specifications parameters agency approvals ce standards gb195110.1-2004/iec61347-1:2003, en55015, en61000, en61547 dimensions 22.00 (0.87) 25.00 (0.98) note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
